Pay in installments of $7.37 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 3 - Jul 8
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
gas pedal accelerator Aluminum Accelerator Pedal Assembly (All Spridgets) – BugeyeguysThis add on accessory is a must for every Spridget with a bottom hinging gas pedal. Here's why Original Bugeye accelerator pedals are a terrible design. They plug into a pivoting metal rod and can easily become un plugged while driving, which is an obvious safety hazard. Once the pedal disconnects, Its not difficult to lodge the rubber pedal on the accelerator rod, thus sticking the throttle OPEN! The other challenge with this original design is the
This add-on accessory is a must for every Spridget with a bottom hinging gas pedal. Here's why...
Original Bugeye accelerator pedals are a terrible design. They plug into a pivoting metal rod and can easily become un-plugged while driving, which is an obvious safety hazard. Once the pedal disconnects, It’s not difficult to lodge the rubber pedal on the accelerator rod, thus sticking the throttle OPEN!
The other challenge with this original design is the hinge mount requires two holes in your nice floor pan. Since it is naturally rusting and making holes on its own, it’s never fun to punch more holes if you don’t have to. Those accelerator holes can become yet another source of corrosion.
Since about 1979 I have been driving my Bugeye ‘Gumby” with just metal bar under my foot and no pedal. And on the cars the we ship to customers, we remove the pedal for safety. Even though it doesn’t look pretty, the bar has been our best solution, until now.
We are exited to offer a nice cast aluminum pad you can easily bolt into place, along with a rubber pedal pad to cover it. This is an elegant solution to an old problem. It’s easy to install and makes heel/toe shifting easy. This is an upgrade that is a winner for every early Sprite!
You get the aluminum bolt on pad, hardware to mount it and a rubber pedal pad, which you will need to install on the aluminum pad before installation.
NOTE: The star washers go in between the aluminum pedal ears and the metal accelerator rod-see photos below. These take up the space and allow for a snug fit before you tighten the bolt. Make sure to tighten the bolt so that the pedal is snug. It can float a little, but make sure to tighten the bolt sufficiently to ensure that the pedal can't flop around. Make sure to use the star washers as shown. Tighten the bolt until the star washers bite into the metal accelerator rod, even if it slightly bends the aluminum "ears" of the casting. The ears may bend slightly, but if the bolt is overtightened the ears can snap, so don't overtighten! We are not responsible for broken ears due to over tightening.
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.8 ★★★★★
Based on 1665 reviews
Sort
Product Reviews
★★★★★ 5
Great product - Add foam product for complete solution
Model: 36 SqFt(3.4 SqM)
Used in two cars with speaker upgrades. Easy to install but get the roller for assured adhesion.removes "tinnyness" from large metal resonators. Use with foam absorptive material for a complete system.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 14, 2026
★★★★★ 5
Great Product for noise reduction in Auto Use.
Model: 36 SqFt(3.4 SqM)
I use this on many builds to dampen the metal echo in cars, vans, and trucks. Just one sheet in the center of a body panel is a huge difference maker. You can also cover the entire surface and get added insulation value. The noise is greatly depleted and it's easy to install with a roller tool. Looks Great when done. Good Product I will use again!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 29, 2025
★★★★★ 5
74 monte carlo Resto
Model: NewSLS50_52
Great product easy installation with sheets cut to size,using for Classic car Restoration,floor pan and doors
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 26, 2026
★★★★★ 5
Impressive Sound Deadening Solution with Enhanced Audio Quality
Model: NewSLS50_52
I recently purchased the Siless 50 mil (1.3mm) 52 sqft Car Sound Deadening mat, and I am delighted with the results it has delivered. Right from the start, I was impressed with the packaging, which ensured the product arrived in perfect condition.
One of the standout features of this sound deadening mat is its ease of use. It was a breeze to cut and modify according to my specific needs. Whether I needed to cover specific areas or customize the size, the mat accommodated my requirements effortlessly. This flexibility made the installation process a breeze.
The Siless Sound Deadening mat has proven to be highly effective in reducing outside noise within my vehicle. With just a half cabin install, I noticed a significant reduction of approximately 10 decibels, making my driving experience much quieter and more comfortable. The mat acted as a reliable barrier against external noise, allowing me to enjoy a more peaceful ride.
Furthermore, the sound quality from my vehicle's audio system experienced a noticeable improvement. The Siless mat effectively dampened vibrations and minimized resonance, resulting in cleaner and more refined audio output. The mat's thickness of 50 mil (1.3mm) ensures optimal sound absorption, contributing to its effectiveness in creating a quieter and more enjoyable driving environment. I can now appreciate the full range of tones and enjoy a more immersive music experience during my drives.
Overall, I highly recommend the Siless 50 mil Car Sound Deadening mat for anyone seeking a reliable and effective solution to reduce noise and enhance audio quality in their vehicle. The easy cutting and modifying process, along with the excellent packaging, contribute to a seamless installation experience. With a significant reduction in outside noise and an improvement in sound system performance, this sound deadening mat has exceeded my expectations.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 27, 2023
★★★★★ 5
Good quality sound deadener at a good price.
Model: NewSLS50_52
Quality sound deadening that adheres to body panels well. You can easily hear the vibration reduction after just the first piece by tapping on the body panel before and after.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on November 21, 2025